#ifndef __S3C24XX_H__
#define __S3C24XX_H__

#define FCLK        400000000
#define HCLK        100000000
#define PCLK        50000000

/* WOTCH DOG register */
#define     WTCON           (*(volatile unsigned long *)0x53000000)
#define     WTDAT           (*(volatile unsigned long *)0x53000004)
#define     WTCNT           (*(volatile unsigned long *)0x53000008)

/* SDRAM regisers */
#define     MEM_CTL_BASE    0x48000000
#define     SDRAM_BASE      0x30000000

/* NAND Flash registers */
#ifdef S3C2410
#define NFCONF              (*(volatile unsigned int  *)0x4e000000)
#define NFCMD               (*(volatile unsigned char *)0x4e000004)
#define NFADDR              (*(volatile unsigned char *)0x4e000008)
#define NFDATA              (*(volatile unsigned char *)0x4e00000c)
#define NFSTAT              (*(volatile unsigned char *)0x4e000010)
#else   /* S3C2440 */
#define NFCONF		        (*(volatile unsigned int  *)0x4e000000)
#define NFCONT		        (*(volatile unsigned short *)0x4e000004)
#define NFCMD		        (*(volatile unsigned char *)0x4e000008)
#define NFADDR		        (*(volatile unsigned short *)0x4e00000C)
#define NFDATA		        (*(volatile unsigned short *)0x4e000010)
#define NFSTAT		        (*(volatile unsigned char *)0x4e000020)
#endif

/* GPIO registers */
#define GPACON              (*(volatile unsigned long *)0x56000000)
#define GPADAT              (*(volatile unsigned long *)0x56000004)

#define GPBCON              (*(volatile unsigned long *)0x56000010)
#define GPBDAT              (*(volatile unsigned long *)0x56000014)
#define GPBUP               (*(volatile unsigned long *)0x56000018)

#define GPCCON              (*(volatile unsigned long *)0x56000020)
#define GPCDAT              (*(volatile unsigned long *)0x56000024)
#define GPCUP               (*(volatile unsigned long *)0x56000028)

#define GPDCON              (*(volatile unsigned long *)0x56000030)
#define GPDDAT              (*(volatile unsigned long *)0x56000034)
#define GPDUP               (*(volatile unsigned long *)0x56000038)

#define GPECON    			(*(volatile unsigned long *)0x56000040)
#define GPEDAT    		    (*(volatile unsigned long *)0x56000044)
#define GPEUP     			(*(volatile unsigned long *)0x56000048)

#define GPFCON              (*(volatile unsigned long *)0x56000050)
#define GPFDAT              (*(volatile unsigned long *)0x56000054)
#define GPFUP               (*(volatile unsigned long *)0x56000058)

#define GPGCON              (*(volatile unsigned long *)0x56000060)
#define GPGDAT              (*(volatile unsigned long *)0x56000064)
#define GPGUP               (*(volatile unsigned long *)0x56000068)

#define GPHCON              (*(volatile unsigned long *)0x56000070)
#define GPHDAT              (*(volatile unsigned long *)0x56000074)
#define GPHUP               (*(volatile unsigned long *)0x56000078)



/*UART registers*/
#define ULCON0              (*(volatile unsigned long *)0x50000000)
#define UCON0               (*(volatile unsigned long *)0x50000004)
#define UFCON0              (*(volatile unsigned long *)0x50000008)
#define UMCON0              (*(volatile unsigned long *)0x5000000c)
#define UTRSTAT0            (*(volatile unsigned long *)0x50000010)
//#define UTXH0               (*(volatile unsigned char *)0x50000020)
//#define URXH0               (*(volatile unsigned char *)0x50000024)
#define UBRDIV0             (*(volatile unsigned long *)0x50000028)


/*interrupt registes*/
#define SRCPND              (*(volatile unsigned long *)0x4A000000)
#define INTMOD              (*(volatile unsigned long *)0x4A000004)
#define INTMSK              (*(volatile unsigned long *)0x4A000008)
#define PRIORITY            (*(volatile unsigned long *)0x4A00000c)
#define INTPND              (*(volatile unsigned long *)0x4A000010)
#define INTOFFSET           (*(volatile unsigned long *)0x4A000014)
#define SUBSRCPND           (*(volatile unsigned long *)0x4A000018)
#define INTSUBMSK           (*(volatile unsigned long *)0x4A00001c)

/*external interrupt registers*/
#define EINTMASK            (*(volatile unsigned long *)0x560000a4)
#define EINTPEND            (*(volatile unsigned long *)0x560000a8)

#define EXTINT0				(*(volatile unsigned *)0x56000088)	//External interrupt control register 0
#define EXTINT1 			(*(volatile unsigned *)0x5600008c)	//External interrupt control register 1
#define EXTINT2				(*(volatile unsigned *)0x56000090)	//External interrupt control register 2

/*clock registers*/
#define	LOCKTIME			(*(volatile unsigned long *)0x4c000000)
#define	MPLLCON				(*(volatile unsigned long *)0x4c000004)
#define	UPLLCON				(*(volatile unsigned long *)0x4c000008)
#define	CLKCON				(*(volatile unsigned long *)0x4c00000c)
#define	CLKSLOW				(*(volatile unsigned long *)0x4c000010)
#define	CLKDIVN				(*(volatile unsigned long *)0x4c000014)


/*PWM & Timer registers*/
#define	TCFG0		(*(volatile unsigned long *)0x51000000)
#define	TCFG1		(*(volatile unsigned long *)0x51000004)
#define	TCON		(*(volatile unsigned long *)0x51000008)
#define	TCNTB0		(*(volatile unsigned short *)0x5100000c)
#define	TCMPB0		(*(volatile unsigned short *)0x51000010)
#define	TCNTO0		(*(volatile unsigned short *)0x51000014)

#define	TCNTB1		(*(volatile unsigned short *)0x51000018)
#define	TCMPB1		(*(volatile unsigned short *)0x5100001c)
#define	TCNTO1		(*(volatile unsigned short *)0x51000020)

#define	TCNTB2		(*(volatile unsigned short *)0x51000024)
#define	TCMPB2		(*(volatile unsigned short *)0x51000028)
#define	TCNTO2		(*(volatile unsigned short *)0x5100002c)

#define	TCNTB3		(*(volatile unsigned short *)0x51000030)
#define	TCMPB3		(*(volatile unsigned short *)0x51000034)
#define	TCNTO3		(*(volatile unsigned short *)0x51000038)

#define	TCNTB4		(*(volatile unsigned short *)0x5100003C)
#define	TCNTO4		(*(volatile unsigned short *)0x51000040)

/* SPI */
#define	SPCON0		(*(volatile unsigned long *)0x59000000)
#define	SPSTA0		(*(volatile unsigned long *)0x59000004)
#define	SPPIN0		(*(volatile unsigned long *)0x59000008)
#define	SPPRE0		(*(volatile unsigned long *)0x5900000C)
#define	SPTDAT0		(*(volatile unsigned char *)0x59000010)
#define	SPRDAT0		(*(volatile unsigned char *)0x59000014)

#define	SPCON1		(*(volatile unsigned long *)0x59000020)
#define	SPSTA1		(*(volatile unsigned long *)0x59000024)
#define	SPPIN1		(*(volatile unsigned long *)0x59000028)
#define	SPPRE1		(*(volatile unsigned long *)0x5900002C)
#define	SPTDAT1		(*(volatile unsigned char *)0x59000030)
#define	SPRDAT1		(*(volatile unsigned char *)0x59000034)

/* I2C registers */
#define IICCON  	(*(volatile unsigned char *)0x54000000) // IIC control
#define IICSTAT 	(*(volatile unsigned char *)0x54000004) // IIC status
#define IICADD  	(*(volatile unsigned char *)0x54000008) // IIC address
#define IICDS   	(*(volatile unsigned char *)0x5400000c) // IIC data shift

// LCD CONTROLLER
#define LCDCON1     (*(volatile unsigned long *)0x4d000000) //LCD control 1
#define LCDCON2     (*(volatile unsigned long *)0x4d000004) //LCD control 2
#define LCDCON3     (*(volatile unsigned long *)0x4d000008) //LCD control 3
#define LCDCON4     (*(volatile unsigned long *)0x4d00000c) //LCD control 4
#define LCDCON5     (*(volatile unsigned long *)0x4d000010) //LCD control 5
#define LCDSADDR1   (*(volatile unsigned long *)0x4d000014) //STN/TFT Frame buffer start address 1
#define LCDSADDR2   (*(volatile unsigned long *)0x4d000018) //STN/TFT Frame buffer start address 2
#define LCDSADDR3   (*(volatile unsigned long *)0x4d00001c) //STN/TFT Virtual screen address set
#define REDLUT      (*(volatile unsigned long *)0x4d000020) //STN Red lookup table
#define GREENLUT    (*(volatile unsigned long *)0x4d000024) //STN Green lookup table 
#define BLUELUT     (*(volatile unsigned long *)0x4d000028) //STN Blue lookup table
#define DITHMODE    (*(volatile unsigned long *)0x4d00004c) //STN Dithering mode
#define TPAL        (*(volatile unsigned long *)0x4d000050) //TFT Temporary palette
#define LCDINTPND   (*(volatile unsigned long *)0x4d000054) //LCD Interrupt pending
#define LCDSRCPND   (*(volatile unsigned long *)0x4d000058) //LCD Interrupt source
#define LCDINTMSK   (*(volatile unsigned long *)0x4d00005c) //LCD Interrupt mask
#define LPCSEL      (*(volatile unsigned long *)0x4d000060) //LPC3600 Control
#define PALETTE     0x4d000400                              //Palette start address

/* ADC registers */
#define ADCCON      (*(volatile unsigned long *)0x58000000)	//ADC control
#define ADCTSC      (*(volatile unsigned long *)0x58000004)	//ADC touch screen control
#define ADCDLY      (*(volatile unsigned long *)0x58000008)	//ADC start or Interval Delay
#define ADCDAT0     (*(volatile unsigned long *)0x5800000c)	//ADC conversion data 0
#define ADCDAT1     (*(volatile unsigned long *)0x58000010)	//ADC conversion data 1
#define ADCUPDN     (*(volatile unsigned long *)0x58000014)	//Stylus Up/Down interrupt status


#define ISR_EINT0_OFT     0
#define ISR_EINT1_OFT     1
#define ISR_EINT2_OFT     2
#define ISR_EINT3_OFT     3
#define ISR_EINT4_7_OFT   4
#define ISR_EINT8_23_OFT  5
#define ISR_NOTUSED6_OFT  6
#define ISR_BAT_FLT_OFT   7
#define ISR_TICK_OFT      8
#define ISR_WDT_OFT       9
#define ISR_TIMER0_OFT    10
#define ISR_TIMER1_OFT    11
#define ISR_TIMER2_OFT    12
#define ISR_TIMER3_OFT    13
#define ISR_TIMER4_OFT    14
#define ISR_UART2_OFT     15
#define ISR_LCD_OFT       16
#define ISR_DMA0_OFT      17
#define ISR_DMA1_OFT      18
#define ISR_DMA2_OFT      19
#define ISR_DMA3_OFT      20
#define ISR_SDI_OFT       21
#define ISR_SPI0_OFT      22
#define ISR_UART1_OFT     23
#define ISR_NOTUSED24_OFT 24
#define ISR_USBD_OFT      25
#define ISR_USBH_OFT      26
#define ISR_IIC_OFT       27
#define ISR_UART0_OFT     28
#define ISR_SPI1_OFT      29
#define ISR_RTC_OFT       30
#define ISR_ADC_OFT       31


// PENDING BIT
#define BIT_EINT0		(0x1)
#define BIT_EINT1		(0x1<<1)
#define BIT_EINT2		(0x1<<2)
#define BIT_EINT3		(0x1<<3)
#define BIT_EINT4_7		(0x1<<4)
#define BIT_EINT8_23	(0x1<<5)
#define BIT_CAM			(0x1<<6)		// Added for 2440.
#define BIT_BAT_FLT		(0x1<<7)
#define BIT_TICK		(0x1<<8)
#define BIT_WDT_AC97	(0x1<<9)
#define BIT_TIMER0		(0x1<<10)
#define BIT_TIMER1		(0x1<<11)
#define BIT_TIMER2		(0x1<<12)
#define BIT_TIMER3		(0x1<<13)
#define BIT_TIMER4		(0x1<<14)
#define BIT_UART2		(0x1<<15)
#define BIT_LCD			(0x1<<16)
#define BIT_DMA0		(0x1<<17)
#define BIT_DMA1		(0x1<<18)
#define BIT_DMA2		(0x1<<19)
#define BIT_DMA3		(0x1<<20)
#define BIT_SDI			(0x1<<21)
#define BIT_SPI0		(0x1<<22)
#define BIT_UART1		(0x1<<23)
#define BIT_NFCON		(0x1<<24)		// Added for 2440.
#define BIT_USBD		(0x1<<25)
#define BIT_USBH		(0x1<<26)
#define BIT_IIC			(0x1<<27)
#define BIT_UART0		(0x1<<28)
#define BIT_SPI1		(0x1<<29)
#define BIT_RTC			(0x1<<30)
#define BIT_ADC			(0x1<<31)
#define BIT_ALLMSK		(0xffffffff)

#define BIT_SUB_ALLMSK	(0x7fff)
#define BIT_SUB_AC97 	(0x1<<14)
#define BIT_SUB_WDT 	(0x1<<13)
#define BIT_SUB_CAM_S	(0x1<<12)		// Added for 2440.
#define BIT_SUB_CAM_C	(0x1<<11)		// Added for 2440.
#define BIT_SUB_ADC		(0x1<<10)
#define BIT_SUB_TC		(0x1<<9)
#define BIT_SUB_ERR2	(0x1<<8)
#define BIT_SUB_TXD2	(0x1<<7)
#define BIT_SUB_RXD2	(0x1<<6)
#define BIT_SUB_ERR1	(0x1<<5)
#define BIT_SUB_TXD1	(0x1<<4)
#define BIT_SUB_RXD1	(0x1<<3)
#define BIT_SUB_ERR0	(0x1<<2)
#define BIT_SUB_TXD0	(0x1<<1)
#define BIT_SUB_RXD0	(0x1<<0)

#define GSTATUS1		(*(volatile unsigned long *)0x560000B0)


/* 下面内容来自mini2440 bsp 2440addr.h */

// Memory control 
#define rBWSCON    (*(volatile unsigned *)0x48000000)	//Bus width & wait status
#define rBANKCON0  (*(volatile unsigned *)0x48000004)	//Boot ROM control
#define rBANKCON1  (*(volatile unsigned *)0x48000008)	//BANK1 control
#define rBANKCON2  (*(volatile unsigned *)0x4800000c)	//BANK2 cControl
#define rBANKCON3  (*(volatile unsigned *)0x48000010)	//BANK3 control
#define rBANKCON4  (*(volatile unsigned *)0x48000014)	//BANK4 control
#define rBANKCON5  (*(volatile unsigned *)0x48000018)	//BANK5 control
#define rBANKCON6  (*(volatile unsigned *)0x4800001c)	//BANK6 control
#define rBANKCON7  (*(volatile unsigned *)0x48000020)	//BANK7 control
#define rREFRESH   (*(volatile unsigned *)0x48000024)	//DRAM/SDRAM refresh
#define rBANKSIZE  (*(volatile unsigned *)0x48000028)	//Flexible Bank Size
#define rMRSRB6    (*(volatile unsigned *)0x4800002c)	//Mode register set for SDRAM
#define rMRSRB7    (*(volatile unsigned *)0x48000030)	//Mode register set for SDRAM


// USB Host


// INTERRUPT
#define rSRCPND     (*(volatile unsigned *)0x4a000000)	//Interrupt request status
#define rINTMOD     (*(volatile unsigned *)0x4a000004)	//Interrupt mode control
#define rINTMSK     (*(volatile unsigned *)0x4a000008)	//Interrupt mask control
#define rPRIORITY   (*(volatile unsigned *)0x4a00000c)	//IRQ priority control
#define rINTPND     (*(volatile unsigned *)0x4a000010)	//Interrupt request status
#define rINTOFFSET  (*(volatile unsigned *)0x4a000014)	//Interruot request source offset
#define rSUBSRCPND  (*(volatile unsigned *)0x4a000018)	//Sub source pending
#define rINTSUBMSK  (*(volatile unsigned *)0x4a00001c)	//Interrupt sub mask


// DMA
#define rDISRC0     (*(volatile unsigned *)0x4b000000)	//DMA 0 Initial source
#define rDISRCC0    (*(volatile unsigned *)0x4b000004)	//DMA 0 Initial source control
#define rDIDST0     (*(volatile unsigned *)0x4b000008)	//DMA 0 Initial Destination
#define rDIDSTC0    (*(volatile unsigned *)0x4b00000c)	//DMA 0 Initial Destination control
#define rDCON0      (*(volatile unsigned *)0x4b000010)	//DMA 0 Control
#define rDSTAT0     (*(volatile unsigned *)0x4b000014)	//DMA 0 Status
#define rDCSRC0     (*(volatile unsigned *)0x4b000018)	//DMA 0 Current source
#define rDCDST0     (*(volatile unsigned *)0x4b00001c)	//DMA 0 Current destination
#define rDMASKTRIG0 (*(volatile unsigned *)0x4b000020)	//DMA 0 Mask trigger

#define rDISRC1     (*(volatile unsigned *)0x4b000040)	//DMA 1 Initial source
#define rDISRCC1    (*(volatile unsigned *)0x4b000044)	//DMA 1 Initial source control
#define rDIDST1     (*(volatile unsigned *)0x4b000048)	//DMA 1 Initial Destination
#define rDIDSTC1    (*(volatile unsigned *)0x4b00004c)	//DMA 1 Initial Destination control
#define rDCON1      (*(volatile unsigned *)0x4b000050)	//DMA 1 Control
#define rDSTAT1     (*(volatile unsigned *)0x4b000054)	//DMA 1 Status
#define rDCSRC1     (*(volatile unsigned *)0x4b000058)	//DMA 1 Current source
#define rDCDST1     (*(volatile unsigned *)0x4b00005c)	//DMA 1 Current destination
#define rDMASKTRIG1 (*(volatile unsigned *)0x4b000060)	//DMA 1 Mask trigger

#define rDISRC2     (*(volatile unsigned *)0x4b000080)	//DMA 2 Initial source
#define rDISRCC2    (*(volatile unsigned *)0x4b000084)	//DMA 2 Initial source control
#define rDIDST2     (*(volatile unsigned *)0x4b000088)	//DMA 2 Initial Destination
#define rDIDSTC2    (*(volatile unsigned *)0x4b00008c)	//DMA 2 Initial Destination control
#define rDCON2      (*(volatile unsigned *)0x4b000090)	//DMA 2 Control
#define rDSTAT2     (*(volatile unsigned *)0x4b000094)	//DMA 2 Status
#define rDCSRC2     (*(volatile unsigned *)0x4b000098)	//DMA 2 Current source
#define rDCDST2     (*(volatile unsigned *)0x4b00009c)	//DMA 2 Current destination
#define rDMASKTRIG2 (*(volatile unsigned *)0x4b0000a0)	//DMA 2 Mask trigger

#define rDISRC3     (*(volatile unsigned *)0x4b0000c0)	//DMA 3 Initial source
#define rDISRCC3    (*(volatile unsigned *)0x4b0000c4)	//DMA 3 Initial source control
#define rDIDST3     (*(volatile unsigned *)0x4b0000c8)	//DMA 3 Initial Destination
#define rDIDSTC3    (*(volatile unsigned *)0x4b0000cc)	//DMA 3 Initial Destination control
#define rDCON3      (*(volatile unsigned *)0x4b0000d0)	//DMA 3 Control
#define rDSTAT3     (*(volatile unsigned *)0x4b0000d4)	//DMA 3 Status
#define rDCSRC3     (*(volatile unsigned *)0x4b0000d8)	//DMA 3 Current source
#define rDCDST3     (*(volatile unsigned *)0x4b0000dc)	//DMA 3 Current destination
#define rDMASKTRIG3 (*(volatile unsigned *)0x4b0000e0)	//DMA 3 Mask trigger


// CLOCK & POWER MANAGEMENT
#define rLOCKTIME   (*(volatile unsigned *)0x4c000000)	//PLL lock time counter
#define rMPLLCON    (*(volatile unsigned *)0x4c000004)	//MPLL Control
#define rUPLLCON    (*(volatile unsigned *)0x4c000008)	//UPLL Control
#define rCLKCON     (*(volatile unsigned *)0x4c00000c)	//Clock generator control
#define rCLKSLOW    (*(volatile unsigned *)0x4c000010)	//Slow clock control
#define rCLKDIVN    (*(volatile unsigned *)0x4c000014)	//Clock divider control
#define rCAMDIVN    (*(volatile unsigned *)0x4c000018)	//USB, CAM Clock divider control


// LCD CONTROLLER
#define rLCDCON1    (*(volatile unsigned *)0x4d000000)	//LCD control 1
#define rLCDCON2    (*(volatile unsigned *)0x4d000004)	//LCD control 2
#define rLCDCON3    (*(volatile unsigned *)0x4d000008)	//LCD control 3
#define rLCDCON4    (*(volatile unsigned *)0x4d00000c)	//LCD control 4
#define rLCDCON5    (*(volatile unsigned *)0x4d000010)	//LCD control 5
#define rLCDSADDR1  (*(volatile unsigned *)0x4d000014)	//STN/TFT Frame buffer start address 1
#define rLCDSADDR2  (*(volatile unsigned *)0x4d000018)	//STN/TFT Frame buffer start address 2
#define rLCDSADDR3  (*(volatile unsigned *)0x4d00001c)	//STN/TFT Virtual screen address set
#define rREDLUT     (*(volatile unsigned *)0x4d000020)	//STN Red lookup table
#define rGREENLUT   (*(volatile unsigned *)0x4d000024)	//STN Green lookup table 
#define rBLUELUT    (*(volatile unsigned *)0x4d000028)	//STN Blue lookup table
#define rDITHMODE   (*(volatile unsigned *)0x4d00004c)	//STN Dithering mode
#define rTPAL       (*(volatile unsigned *)0x4d000050)	//TFT Temporary palette
#define rLCDINTPND  (*(volatile unsigned *)0x4d000054)	//LCD Interrupt pending
#define rLCDSRCPND  (*(volatile unsigned *)0x4d000058)	//LCD Interrupt source
#define rLCDINTMSK  (*(volatile unsigned *)0x4d00005c)	//LCD Interrupt mask
#define rTCONSEL    (*(volatile unsigned *)0x4d000060)	//LPC3600 Control --- edited by junon
#define PALETTE     (0x4d000400)						//Palette start address


//Nand Flash
#define rNFCONF		(*(volatile unsigned *)0x4E000000)		//NAND Flash configuration
#define rNFCONT		(*(volatile unsigned *)0x4E000004)      //NAND Flash control
#define rNFCMD		(*(volatile unsigned *)0x4E000008)      //NAND Flash command
#define rNFADDR		(*(volatile unsigned *)0x4E00000C)      //NAND Flash address
#define rNFDATA		(*(volatile unsigned *)0x4E000010)      //NAND Flash data
#define rNFDATA8	(*(volatile unsigned char *)0x4E000010) //NAND Flash data
#define NFDATA		(0x4E000010)      						//NAND Flash data address
#define rNFMECCD0	(*(volatile unsigned *)0x4E000014)      //NAND Flash ECC for Main Area
#define rNFMECCD1	(*(volatile unsigned *)0x4E000018)
#define rNFSECCD	(*(volatile unsigned *)0x4E00001C)		//NAND Flash ECC for Spare Area
#define rNFSTAT		(*(volatile unsigned char *)0x4E000020)	//NAND Flash operation status
#define rNFESTAT0	(*(volatile unsigned *)0x4E000024)
#define rNFESTAT1	(*(volatile unsigned *)0x4E000028)
#define rNFMECC0	(*(volatile unsigned *)0x4E00002C)
#define rNFMECC1	(*(volatile unsigned *)0x4E000030)
#define rNFSECC		(*(volatile unsigned *)0x4E000034)
#define rNFSBLK		(*(volatile unsigned *)0x4E000038)		//NAND Flash Start block address
#define rNFEBLK		(*(volatile unsigned *)0x4E00003C)		//NAND Flash End block address


//Camera Interface			                       
#define	rASIZE				(*(volatile unsigned *)0x4F000000)        
#define	rSTAY1				(*(volatile unsigned *)0x4F000004)        
#define	rSTAY2				(*(volatile unsigned *)0x4F000008)        
#define	rSTAY3				(*(volatile unsigned *)0x4F00000C)        
#define	rSTAY4				(*(volatile unsigned *)0x4F000010)        
#define	rAYBURST			(*(volatile unsigned *)0x4F000014)
#define	rACBBURST			(*(volatile unsigned *)0x4F000018)
#define	rACRBURST			(*(volatile unsigned *)0x4F00001C)
#define	rBSIZE				(*(volatile unsigned *)0x4F000020)        
#define	rSTBY1				(*(volatile unsigned *)0x4F000024)        
#define	rSTBY2				(*(volatile unsigned *)0x4F000028)        
#define	rSTBY3				(*(volatile unsigned *)0x4F00002C)        
#define	rSTBY4				(*(volatile unsigned *)0x4F000030)        
#define	rBYBURST			(*(volatile unsigned *)0x4F000034)
#define	rBCBBURST			(*(volatile unsigned *)0x4F000038)
#define	rBCRBURST			(*(volatile unsigned *)0x4F00003C)
#define	rADISTWIDTH			(*(volatile unsigned *)0x4F000040)
#define	rBDISTWIDTH			(*(volatile unsigned *)0x4F000044)
#define	rYRATIO				(*(volatile unsigned *)0x4F00004C)        
#define	rCRATIO				(*(volatile unsigned *)0x4F000050)        
#define	rYORIGINAL			(*(volatile unsigned *)0x4F000054)
#define	rCORIGINAL			(*(volatile unsigned *)0x4F00005C)
#define	rSTACB1				(*(volatile unsigned *)0x4F000074)        
#define	rSTACB2				(*(volatile unsigned *)0x4F000078)        
#define	rSTACB3				(*(volatile unsigned *)0x4F00007C)        
#define	rSTACB4				(*(volatile unsigned *)0x4F000080)        
#define	rSTACR1				(*(volatile unsigned *)0x4F000084)        
#define	rSTACR2				(*(volatile unsigned *)0x4F000088)        
#define	rSTACR3				(*(volatile unsigned *)0x4F00008C)        
#define	rSTACR4				(*(volatile unsigned *)0x4F000090)        
#define	rSTBCB1				(*(volatile unsigned *)0x4F00009C)        
#define	rSTBCB2				(*(volatile unsigned *)0x4F0000A0)        
#define	rSTBCB3				(*(volatile unsigned *)0x4F0000A4)        
#define	rSTBCB4				(*(volatile unsigned *)0x4F0000A8)        
#define	rSTBCR1				(*(volatile unsigned *)0x4F0000AC)        
#define	rSTBCR2				(*(volatile unsigned *)0x4F0000B0)        
#define	rSTBCR3				(*(volatile unsigned *)0x4F0000B4)        
#define	rSTBCR4				(*(volatile unsigned *)0x4F0000B8)        
#define	rCTRL_C				(*(volatile unsigned *)0x4F0000BC)        
// read only register
#define	rRDSTAT				(*(volatile unsigned *)0x4F000000)        
#define	rRDSTAY				(*(volatile unsigned *)0x4F000014)        
#define	rRDSTACB			(*(volatile unsigned *)0x4F000018)
#define	rRDSTACR			(*(volatile unsigned *)0x4F00001C)
#define	rRDSTACB1			(*(volatile unsigned *)0x4F000020)
#define	rRDSTACR1			(*(volatile unsigned *)0x4F000024)
#define	rRDSTBY1			(*(volatile unsigned *)0x4F000028)
#define	rRDSTBY2			(*(volatile unsigned *)0x4F00002C)
#define	rRDSTBY3			(*(volatile unsigned *)0x4F000030)
#define	rRDSTBY4			(*(volatile unsigned *)0x4F000034)
#define	rRDSTBY				(*(volatile unsigned *)0x4F000038)        
#define	rRDSTBCB			(*(volatile unsigned *)0x4F00003C)
#define	rRDSTBCR			(*(volatile unsigned *)0x4F000040)
#define	rRDSTBCB1			(*(volatile unsigned *)0x4F000044)
#define	rRDSTBCR1			(*(volatile unsigned *)0x4F000048)
#define	rRDADISTWIDTH		(*(volatile unsigned *)0x4F00004C)
#define	rRDBDISTWIDTH		(*(volatile unsigned *)0x4F000050)


// UART
#define rULCON0     (*(volatile unsigned *)0x50000000)	//UART 0 Line control
#define rUCON0      (*(volatile unsigned *)0x50000004)	//UART 0 Control
#define rUFCON0     (*(volatile unsigned *)0x50000008)	//UART 0 FIFO control
#define rUMCON0     (*(volatile unsigned *)0x5000000c)	//UART 0 Modem control
#define rUTRSTAT0   (*(volatile unsigned *)0x50000010)	//UART 0 Tx/Rx status
#define rUERSTAT0   (*(volatile unsigned *)0x50000014)	//UART 0 Rx error status
#define rUFSTAT0    (*(volatile unsigned *)0x50000018)	//UART 0 FIFO status
#define rUMSTAT0    (*(volatile unsigned *)0x5000001c)	//UART 0 Modem status
#define rUBRDIV0    (*(volatile unsigned *)0x50000028)	//UART 0 Baud rate divisor

#define rULCON1     (*(volatile unsigned *)0x50004000)	//UART 1 Line control
#define rUCON1      (*(volatile unsigned *)0x50004004)	//UART 1 Control
#define rUFCON1     (*(volatile unsigned *)0x50004008)	//UART 1 FIFO control
#define rUMCON1     (*(volatile unsigned *)0x5000400c)	//UART 1 Modem control
#define rUTRSTAT1   (*(volatile unsigned *)0x50004010)	//UART 1 Tx/Rx status
#define rUERSTAT1   (*(volatile unsigned *)0x50004014)	//UART 1 Rx error status
#define rUFSTAT1    (*(volatile unsigned *)0x50004018)	//UART 1 FIFO status
#define rUMSTAT1    (*(volatile unsigned *)0x5000401c)	//UART 1 Modem status
#define rUBRDIV1    (*(volatile unsigned *)0x50004028)	//UART 1 Baud rate divisor
#define rULCON2     (*(volatile unsigned *)0x50008000)	//UART 2 Line control
#define rUCON2      (*(volatile unsigned *)0x50008004)	//UART 2 Control
#define rUFCON2     (*(volatile unsigned *)0x50008008)	//UART 2 FIFO control
#define rUMCON2     (*(volatile unsigned *)0x5000800c)	//UART 2 Modem control
#define rUTRSTAT2   (*(volatile unsigned *)0x50008010)	//UART 2 Tx/Rx status
#define rUERSTAT2   (*(volatile unsigned *)0x50008014)	//UART 2 Rx error status
#define rUFSTAT2    (*(volatile unsigned *)0x50008018)	//UART 2 FIFO status
#define rUMSTAT2    (*(volatile unsigned *)0x5000801c)	//UART 2 Modem status
#define rUBRDIV2    (*(volatile unsigned *)0x50008028)	//UART 2 Baud rate divisor

#ifdef __BIG_ENDIAN
#define rUTXH0      (*(volatile unsigned char *)0x50000023)	//UART 0 Transmission Hold
#define rURXH0      (*(volatile unsigned char *)0x50000027)	//UART 0 Receive buffer
#define rUTXH1      (*(volatile unsigned char *)0x50004023)	//UART 1 Transmission Hold
#define rURXH1      (*(volatile unsigned char *)0x50004027)	//UART 1 Receive buffer
#define rUTXH2      (*(volatile unsigned char *)0x50008023)	//UART 2 Transmission Hold
#define rURXH2      (*(volatile unsigned char *)0x50008027)	//UART 2 Receive buffer

#define WrUTXH0(ch) (*(volatile unsigned char *)0x50000023)=(unsigned char)(ch)
#define RdURXH0()   (*(volatile unsigned char *)0x50000027)
#define WrUTXH1(ch) (*(volatile unsigned char *)0x50004023)=(unsigned char)(ch)
#define RdURXH1()   (*(volatile unsigned char *)0x50004027)
#define WrUTXH2(ch) (*(volatile unsigned char *)0x50008023)=(unsigned char)(ch)
#define RdURXH2()   (*(volatile unsigned char *)0x50008027)

#define UTXH0       (*(volatile unsigned long *)(0x50000020+3))  //Byte_access address by DMA
#define URXH0       (*(volatile unsigned long *)(0x50000024+3))
#define UTXH1       (*(volatile unsigned long *)(0x50004020+3))
#define URXH1       (*(volatile unsigned long *)(0x50004024+3))
#define UTXH2       (*(volatile unsigned long *)(0x50008020+3))
#define URXH2       (*(volatile unsigned long *)(0x50008024+3))

#else //Little Endian
#define rUTXH0		(*(volatile unsigned char *)0x50000020)	//UART 0 Transmission Hold
#define rURXH0		(*(volatile unsigned char *)0x50000024)	//UART 0 Receive buffer
#define rUTXH1		(*(volatile unsigned char *)0x50004020)	//UART 1 Transmission Hold
#define rURXH1		(*(volatile unsigned char *)0x50004024)	//UART 1 Receive buffer
#define rUTXH2		(*(volatile unsigned char *)0x50008020)	//UART 2 Transmission Hold
#define rURXH2		(*(volatile unsigned char *)0x50008024)	//UART 2 Receive buffer

#define WrUTXH0(ch) (*(volatile unsigned char *)0x50000020)=(unsigned char)(ch)
#define RdURXH0()   (*(volatile unsigned char *)0x50000024)
#define WrUTXH1(ch) (*(volatile unsigned char *)0x50004020)=(unsigned char)(ch)
#define RdURXH1()   (*(volatile unsigned char *)0x50004024)
#define WrUTXH2(ch) (*(volatile unsigned char *)0x50008020)=(unsigned char)(ch)
#define RdURXH2()   (*(volatile unsigned char *)0x50008024)

#define UTXH0       (*(volatile unsigned long *)(0x50000020))  //Byte_access address by DMA
#define URXH0       (*(volatile unsigned long *)(0x50000024))
#define UTXH1       (*(volatile unsigned long *)(0x50004020))
#define URXH1       (*(volatile unsigned long *)(0x50004024))
#define UTXH2       (*(volatile unsigned long *)(0x50008020))
#define URXH2       (*(volatile unsigned long *)(0x50008024))

#endif


// PWM TIMER
#define rTCFG0  (*(volatile unsigned *)0x51000000)	//Timer 0 configuration
#define rTCFG1  (*(volatile unsigned *)0x51000004)	//Timer 1 configuration
#define rTCON   (*(volatile unsigned *)0x51000008)	//Timer control
#define rTCNTB0 (*(volatile unsigned *)0x5100000c)	//Timer count buffer 0
#define rTCMPB0 (*(volatile unsigned *)0x51000010)	//Timer compare buffer 0
#define rTCNTO0 (*(volatile unsigned *)0x51000014)	//Timer count observation 0
#define rTCNTB1 (*(volatile unsigned *)0x51000018)	//Timer count buffer 1
#define rTCMPB1 (*(volatile unsigned *)0x5100001c)	//Timer compare buffer 1
#define rTCNTO1 (*(volatile unsigned *)0x51000020)	//Timer count observation 1
#define rTCNTB2 (*(volatile unsigned *)0x51000024)	//Timer count buffer 2
#define rTCMPB2 (*(volatile unsigned *)0x51000028)	//Timer compare buffer 2
#define rTCNTO2 (*(volatile unsigned *)0x5100002c)	//Timer count observation 2
#define rTCNTB3 (*(volatile unsigned *)0x51000030)	//Timer count buffer 3
#define rTCMPB3 (*(volatile unsigned *)0x51000034)	//Timer compare buffer 3
#define rTCNTO3 (*(volatile unsigned *)0x51000038)	//Timer count observation 3
#define rTCNTB4 (*(volatile unsigned *)0x5100003c)	//Timer count buffer 4
#define rTCNTO4 (*(volatile unsigned *)0x51000040)	//Timer count observation 4

// USB HOST
#define rHcRevision			(*(volatile unsigned *)0x49000000)
#define rHcControl			(*(volatile unsigned *)0x49000004)
#define rHcCommonStatus     (*(volatile unsigned *)0x49000008)
#define rHcInterruptStatus  (*(volatile unsigned *)0x4900000C)
#define rHcInterruptEnable  (*(volatile unsigned *)0x49000010)
#define rHcInterruptDisable (*(volatile unsigned *)0x49000014)
#define rHcHCCA				(*(volatile unsigned *)0x49000018)
#define rHcPeriodCuttendED  (*(volatile unsigned *)0x4900001C)
#define rHcControlHeadED    (*(volatile unsigned *)0x49000020)
#define rHcControlCurrentED (*(volatile unsigned *)0x49000024)
#define rHcBulkHeadED       (*(volatile unsigned *)0x49000028)
#define rHcBuldCurrentED    (*(volatile unsigned *)0x4900002C)
#define rHcDoneHead			(*(volatile unsigned *)0x49000030)
#define rHcRmInterval       (*(volatile unsigned *)0x49000034)
#define rHcFmRemaining      (*(volatile unsigned *)0x49000038)
#define rHcFmNumber			(*(volatile unsigned *)0x4900003C)
#define rHcPeriodicStart    (*(volatile unsigned *)0x49000040)
#define rHcLSThreshold      (*(volatile unsigned *)0x49000044)
#define rHcRhDescriptorA    (*(volatile unsigned *)0x49000048)
#define rHcRhDescriptorB    (*(volatile unsigned *)0x4900004C)
#define rHcRhStatus			(*(volatile unsigned *)0x49000050)
#define rHcRhPortStatus1    (*(volatile unsigned *)0x49000054)
#define rHcRhPortStatus2    (*(volatile unsigned *)0x49000058)

// USB DEVICE
#ifdef __BIG_ENDIAN
#define rFUNC_ADDR_REG     (*(volatile unsigned char *)0x52000143)	//Function address
#define rPWR_REG           (*(volatile unsigned char *)0x52000147)	//Power management
#define rEP_INT_REG        (*(volatile unsigned char *)0x5200014b)	//EP Interrupt pending and clear
#define rUSB_INT_REG       (*(volatile unsigned char *)0x5200015b)	//USB Interrupt pending and clear
#define rEP_INT_EN_REG     (*(volatile unsigned char *)0x5200015f)	//Interrupt enable
#define rUSB_INT_EN_REG    (*(volatile unsigned char *)0x5200016f)
#define rFRAME_NUM1_REG    (*(volatile unsigned char *)0x52000173)	//Frame number lower byte
#define rFRAME_NUM2_REG    (*(volatile unsigned char *)0x52000177)	//Frame number higher byte
#define rINDEX_REG         (*(volatile unsigned char *)0x5200017b)	//Register index
#define rMAXP_REG          (*(volatile unsigned char *)0x52000183)	//Endpoint max packet
#define rEP0_CSR           (*(volatile unsigned char *)0x52000187)	//Endpoint 0 status
#define rIN_CSR1_REG       (*(volatile unsigned char *)0x52000187)	//In endpoint control status
#define rIN_CSR2_REG       (*(volatile unsigned char *)0x5200018b)
#define rOUT_CSR1_REG      (*(volatile unsigned char *)0x52000193)	//Out endpoint control status
#define rOUT_CSR2_REG      (*(volatile unsigned char *)0x52000197)
#define rOUT_FIFO_CNT1_REG (*(volatile unsigned char *)0x5200019b)	//Endpoint out write count
#define rOUT_FIFO_CNT2_REG (*(volatile unsigned char *)0x5200019f)
#define rEP0_FIFO          (*(volatile unsigned char *)0x520001c3)	//Endpoint 0 FIFO
#define rEP1_FIFO          (*(volatile unsigned char *)0x520001c7)	//Endpoint 1 FIFO
#define rEP2_FIFO          (*(volatile unsigned char *)0x520001cb)	//Endpoint 2 FIFO
#define rEP3_FIFO          (*(volatile unsigned char *)0x520001cf)	//Endpoint 3 FIFO
#define rEP4_FIFO          (*(volatile unsigned char *)0x520001d3)	//Endpoint 4 FIFO
#define rEP1_DMA_CON       (*(volatile unsigned char *)0x52000203)	//EP1 DMA interface control
#define rEP1_DMA_UNIT      (*(volatile unsigned char *)0x52000207)	//EP1 DMA Tx unit counter
#define rEP1_DMA_FIFO      (*(volatile unsigned char *)0x5200020b)	//EP1 DMA Tx FIFO counter
#define rEP1_DMA_TX_LO     (*(volatile unsigned char *)0x5200020f)	//EP1 DMA total Tx counter
#define rEP1_DMA_TX_MD     (*(volatile unsigned char *)0x52000213)
#define rEP1_DMA_TX_HI     (*(volatile unsigned char *)0x52000217)
#define rEP2_DMA_CON       (*(volatile unsigned char *)0x5200021b)	//EP2 DMA interface control
#define rEP2_DMA_UNIT      (*(volatile unsigned char *)0x5200021f)	//EP2 DMA Tx unit counter
#define rEP2_DMA_FIFO      (*(volatile unsigned char *)0x52000223)	//EP2 DMA Tx FIFO counter
#define rEP2_DMA_TX_LO     (*(volatile unsigned char *)0x52000227)	//EP2 DMA total Tx counter
#define rEP2_DMA_TX_MD     (*(volatile unsigned char *)0x5200022b)
#define rEP2_DMA_TX_HI     (*(volatile unsigned char *)0x5200022f)
#define rEP3_DMA_CON       (*(volatile unsigned char *)0x52000243)	//EP3 DMA interface control
#define rEP3_DMA_UNIT      (*(volatile unsigned char *)0x52000247)	//EP3 DMA Tx unit counter
#define rEP3_DMA_FIFO      (*(volatile unsigned char *)0x5200024b)	//EP3 DMA Tx FIFO counter
#define rEP3_DMA_TX_LO     (*(volatile unsigned char *)0x5200024f)	//EP3 DMA total Tx counter
#define rEP3_DMA_TX_MD     (*(volatile unsigned char *)0x52000253)
#define rEP3_DMA_TX_HI     (*(volatile unsigned char *)0x52000257) 
#define rEP4_DMA_CON       (*(volatile unsigned char *)0x5200025b)	//EP4 DMA interface control
#define rEP4_DMA_UNIT      (*(volatile unsigned char *)0x5200025f)	//EP4 DMA Tx unit counter
#define rEP4_DMA_FIFO      (*(volatile unsigned char *)0x52000263)	//EP4 DMA Tx FIFO counter
#define rEP4_DMA_TX_LO     (*(volatile unsigned char *)0x52000267)	//EP4 DMA total Tx counter
#define rEP4_DMA_TX_MD     (*(volatile unsigned char *)0x5200026b)
#define rEP4_DMA_TX_HI     (*(volatile unsigned char *)0x5200026f)

#else  // Little Endian
#define rFUNC_ADDR_REG     (*(volatile unsigned char *)0x52000140)	//Function address
#define rPWR_REG           (*(volatile unsigned char *)0x52000144)	//Power management
#define rEP_INT_REG        (*(volatile unsigned char *)0x52000148)	//EP Interrupt pending and clear
#define rUSB_INT_REG       (*(volatile unsigned char *)0x52000158)	//USB Interrupt pending and clear
#define rEP_INT_EN_REG     (*(volatile unsigned char *)0x5200015c)	//Interrupt enable
#define rUSB_INT_EN_REG    (*(volatile unsigned char *)0x5200016c)
#define rFRAME_NUM1_REG    (*(volatile unsigned char *)0x52000170)	//Frame number lower byte
#define rFRAME_NUM2_REG    (*(volatile unsigned char *)0x52000174)	//Frame number higher byte
#define rINDEX_REG         (*(volatile unsigned char *)0x52000178)	//Register index
#define rMAXP_REG          (*(volatile unsigned char *)0x52000180)	//Endpoint max packet
#define rEP0_CSR           (*(volatile unsigned char *)0x52000184)	//Endpoint 0 status
#define rIN_CSR1_REG       (*(volatile unsigned char *)0x52000184)	//In endpoint control status
#define rIN_CSR2_REG       (*(volatile unsigned char *)0x52000188)
#define rOUT_CSR1_REG      (*(volatile unsigned char *)0x52000190)	//Out endpoint control status
#define rOUT_CSR2_REG      (*(volatile unsigned char *)0x52000194)
#define rOUT_FIFO_CNT1_REG (*(volatile unsigned char *)0x52000198)	//Endpoint out write count
#define rOUT_FIFO_CNT2_REG (*(volatile unsigned char *)0x5200019c)
#define rEP0_FIFO          (*(volatile unsigned char *)0x520001c0)	//Endpoint 0 FIFO
#define rEP1_FIFO          (*(volatile unsigned char *)0x520001c4)	//Endpoint 1 FIFO
#define rEP2_FIFO          (*(volatile unsigned char *)0x520001c8)	//Endpoint 2 FIFO
#define rEP3_FIFO          (*(volatile unsigned char *)0x520001cc)	//Endpoint 3 FIFO
#define rEP4_FIFO          (*(volatile unsigned char *)0x520001d0)	//Endpoint 4 FIFO
#define rEP1_DMA_CON       (*(volatile unsigned char *)0x52000200)	//EP1 DMA interface control
#define rEP1_DMA_UNIT      (*(volatile unsigned char *)0x52000204)	//EP1 DMA Tx unit counter
#define rEP1_DMA_FIFO      (*(volatile unsigned char *)0x52000208)	//EP1 DMA Tx FIFO counter
#define rEP1_DMA_TX_LO     (*(volatile unsigned char *)0x5200020c)	//EP1 DMA total Tx counter
#define rEP1_DMA_TX_MD     (*(volatile unsigned char *)0x52000210)
#define rEP1_DMA_TX_HI     (*(volatile unsigned char *)0x52000214)
#define rEP2_DMA_CON       (*(volatile unsigned char *)0x52000218)	//EP2 DMA interface control
#define rEP2_DMA_UNIT      (*(volatile unsigned char *)0x5200021c)	//EP2 DMA Tx unit counter
#define rEP2_DMA_FIFO      (*(volatile unsigned char *)0x52000220)	//EP2 DMA Tx FIFO counter
#define rEP2_DMA_TX_LO     (*(volatile unsigned char *)0x52000224)	//EP2 DMA total Tx counter
#define rEP2_DMA_TX_MD     (*(volatile unsigned char *)0x52000228)
#define rEP2_DMA_TX_HI     (*(volatile unsigned char *)0x5200022c)
#define rEP3_DMA_CON       (*(volatile unsigned char *)0x52000240)	//EP3 DMA interface control
#define rEP3_DMA_UNIT      (*(volatile unsigned char *)0x52000244)	//EP3 DMA Tx unit counter
#define rEP3_DMA_FIFO      (*(volatile unsigned char *)0x52000248)	//EP3 DMA Tx FIFO counter
#define rEP3_DMA_TX_LO     (*(volatile unsigned char *)0x5200024c)	//EP3 DMA total Tx counter
#define rEP3_DMA_TX_MD     (*(volatile unsigned char *)0x52000250)
#define rEP3_DMA_TX_HI     (*(volatile unsigned char *)0x52000254)
#define rEP4_DMA_CON       (*(volatile unsigned char *)0x52000258)	//EP4 DMA interface control
#define rEP4_DMA_UNIT      (*(volatile unsigned char *)0x5200025c)	//EP4 DMA Tx unit counter
#define rEP4_DMA_FIFO      (*(volatile unsigned char *)0x52000260)	//EP4 DMA Tx FIFO counter
#define rEP4_DMA_TX_LO     (*(volatile unsigned char *)0x52000264)	//EP4 DMA total Tx counter
#define rEP4_DMA_TX_MD     (*(volatile unsigned char *)0x52000268)
#define rEP4_DMA_TX_HI     (*(volatile unsigned char *)0x5200026c)
#endif   // __BIG_ENDIAN


// WATCH DOG TIMER
#define rWTCON   (*(volatile unsigned *)0x53000000)	//Watch-dog timer mode
#define rWTDAT   (*(volatile unsigned *)0x53000004)	//Watch-dog timer data
#define rWTCNT   (*(volatile unsigned *)0x53000008)	//Eatch-dog timer count


// IIC
#define rIICCON		(*(volatile unsigned *)0x54000000)	//IIC control
#define rIICSTAT	(*(volatile unsigned *)0x54000004)	//IIC status
#define rIICADD		(*(volatile unsigned *)0x54000008)	//IIC address
#define rIICDS		(*(volatile unsigned *)0x5400000c)	//IIC data shift
#define rIICLC		(*(volatile unsigned *)0x54000010)	//IIC multi-master line control


// IIS
#define rIISCON  (*(volatile unsigned *)0x55000000)	//IIS Control
#define rIISMOD  (*(volatile unsigned *)0x55000004)	//IIS Mode
#define rIISPSR  (*(volatile unsigned *)0x55000008)	//IIS Prescaler
#define rIISFCON (*(volatile unsigned *)0x5500000c)	//IIS FIFO control
#ifdef __BIG_ENDIAN
#define IISFIFO  ((volatile unsigned short *)0x55000012)	//IIS FIFO entry
#else //Little Endian
#define IISFIFO  ((volatile unsigned short *)0x55000010)	//IIS FIFO entry
#endif


// I/O PORT 
#define rGPACON    (*(volatile unsigned *)0x56000000)	//Port A control
#define rGPADAT    (*(volatile unsigned *)0x56000004)	//Port A data

#define rGPBCON    (*(volatile unsigned *)0x56000010)	//Port B control
#define rGPBDAT    (*(volatile unsigned *)0x56000014)	//Port B data
#define rGPBUP     (*(volatile unsigned *)0x56000018)	//Pull-up control B

#define rGPCCON    (*(volatile unsigned *)0x56000020)	//Port C control
#define rGPCDAT    (*(volatile unsigned *)0x56000024)	//Port C data
#define rGPCUP     (*(volatile unsigned *)0x56000028)	//Pull-up control C

#define rGPDCON    (*(volatile unsigned *)0x56000030)	//Port D control
#define rGPDDAT    (*(volatile unsigned *)0x56000034)	//Port D data
#define rGPDUP     (*(volatile unsigned *)0x56000038)	//Pull-up control D

#define rGPECON    (*(volatile unsigned *)0x56000040)	//Port E control
#define rGPEDAT    (*(volatile unsigned *)0x56000044)	//Port E data
#define rGPEUP     (*(volatile unsigned *)0x56000048)	//Pull-up control E

#define rGPFCON    (*(volatile unsigned *)0x56000050)	//Port F control
#define rGPFDAT    (*(volatile unsigned *)0x56000054)	//Port F data
#define rGPFUP     (*(volatile unsigned *)0x56000058)	//Pull-up control F

#define rGPGCON    (*(volatile unsigned *)0x56000060)	//Port G control
#define rGPGDAT    (*(volatile unsigned *)0x56000064)	//Port G data
#define rGPGUP     (*(volatile unsigned *)0x56000068)	//Pull-up control G

#define rGPHCON    (*(volatile unsigned *)0x56000070)	//Port H control
#define rGPHDAT    (*(volatile unsigned *)0x56000074)	//Port H data
#define rGPHUP     (*(volatile unsigned *)0x56000078)	//Pull-up control H

#define rGPJCON    (*(volatile unsigned *)0x560000d0)	//Port J control
#define rGPJDAT    (*(volatile unsigned *)0x560000d4)	//Port J data
#define rGPJUP     (*(volatile unsigned *)0x560000d8)	//Pull-up control J

#define rMISCCR    (*(volatile unsigned *)0x56000080)	//Miscellaneous control
#define rDCLKCON   (*(volatile unsigned *)0x56000084)	//DCLK0/1 control
#define rEXTINT0   (*(volatile unsigned *)0x56000088)	//External interrupt control register 0
#define rEXTINT1   (*(volatile unsigned *)0x5600008c)	//External interrupt control register 1
#define rEXTINT2   (*(volatile unsigned *)0x56000090)	//External interrupt control register 2
#define rEINTFLT0  (*(volatile unsigned *)0x56000094)	//Reserved
#define rEINTFLT1  (*(volatile unsigned *)0x56000098)	//Reserved
#define rEINTFLT2  (*(volatile unsigned *)0x5600009c)	//External interrupt filter control register 2
#define rEINTFLT3  (*(volatile unsigned *)0x560000a0)	//External interrupt filter control register 3
#define rEINTMASK  (*(volatile unsigned *)0x560000a4)	//External interrupt mask
#define rEINTPEND  (*(volatile unsigned *)0x560000a8)	//External interrupt pending
#define rGSTATUS0  (*(volatile unsigned *)0x560000ac)	//External pin status
#define rGSTATUS1  (*(volatile unsigned *)0x560000b0)	//Chip ID(0x32440000)
#define rGSTATUS2  (*(volatile unsigned *)0x560000b4)	//Reset type
#define rGSTATUS3  (*(volatile unsigned *)0x560000b8)	//Saved data0(32-bit) before entering POWER_OFF mode 
#define rGSTATUS4  (*(volatile unsigned *)0x560000bc)	//Saved data0(32-bit) before entering POWER_OFF mode 

#define isS3C2410  ((rGSTATUS1 & 0xffff0000) == 0x32410000)
// Added for 2440
#define rFLTOUT		(*(volatile unsigned *)0x560000c0)	// Filter output(Read only)
#define rDSC0			(*(volatile unsigned *)0x560000c4)	// Strength control register 0
#define rDSC1			(*(volatile unsigned *)0x560000c8)	// Strength control register 1
#define rMSLCON		(*(volatile unsigned *)0x560000cc)	// Memory sleep control register

// RTC
#ifdef __BIG_ENDIAN
#define rRTCCON    (*(volatile unsigned char *)0x57000043)	//RTC control
#define rTICNT     (*(volatile unsigned char *)0x57000047)	//Tick time count
#define rRTCALM    (*(volatile unsigned char *)0x57000053)	//RTC alarm control
#define rALMSEC    (*(volatile unsigned char *)0x57000057)	//Alarm second
#define rALMMIN    (*(volatile unsigned char *)0x5700005b)	//Alarm minute
#define rALMHOUR   (*(volatile unsigned char *)0x5700005f)	//Alarm Hour
#define rALMDATE   (*(volatile unsigned char *)0x57000063)	//Alarm date   //edited by junon
#define rALMMON    (*(volatile unsigned char *)0x57000067)	//Alarm month
#define rALMYEAR   (*(volatile unsigned char *)0x5700006b)	//Alarm year
#define rRTCRST    (*(volatile unsigned char *)0x5700006f)	//RTC round reset
#define rBCDSEC    (*(volatile unsigned char *)0x57000073)	//BCD second
#define rBCDMIN    (*(volatile unsigned char *)0x57000077)	//BCD minute
#define rBCDHOUR   (*(volatile unsigned char *)0x5700007b)	//BCD hour
#define rBCDDATE   (*(volatile unsigned char *)0x5700007f)	//BCD date  //edited by junon
#define rBCDDAY    (*(volatile unsigned char *)0x57000083)	//BCD day   //edited by junon
#define rBCDMON    (*(volatile unsigned char *)0x57000087)	//BCD month
#define rBCDYEAR   (*(volatile unsigned char *)0x5700008b)	//BCD year

#else //Little Endian
#define rRTCCON    (*(volatile unsigned char *)0x57000040)	//RTC control
#define rTICNT     (*(volatile unsigned char *)0x57000044)	//Tick time count
#define rRTCALM    (*(volatile unsigned char *)0x57000050)	//RTC alarm control
#define rALMSEC    (*(volatile unsigned char *)0x57000054)	//Alarm second
#define rALMMIN    (*(volatile unsigned char *)0x57000058)	//Alarm minute
#define rALMHOUR   (*(volatile unsigned char *)0x5700005c)	//Alarm Hour
#define rALMDATE   (*(volatile unsigned char *)0x57000060)	//Alarm date  // edited by junon
#define rALMMON    (*(volatile unsigned char *)0x57000064)	//Alarm month
#define rALMYEAR   (*(volatile unsigned char *)0x57000068)	//Alarm year
#define rRTCRST    (*(volatile unsigned char *)0x5700006c)	//RTC round reset
#define rBCDSEC    (*(volatile unsigned char *)0x57000070)	//BCD second
#define rBCDMIN    (*(volatile unsigned char *)0x57000074)	//BCD minute
#define rBCDHOUR   (*(volatile unsigned char *)0x57000078)	//BCD hour
#define rBCDDATE   (*(volatile unsigned char *)0x5700007c)	//BCD date  //edited by junon
#define rBCDDAY    (*(volatile unsigned char *)0x57000080)	//BCD day   //edited by junon
#define rBCDMON    (*(volatile unsigned char *)0x57000084)	//BCD month
#define rBCDYEAR   (*(volatile unsigned char *)0x57000088)	//BCD year
#endif  //RTC


// ADC
#define rADCCON    (*(volatile unsigned *)0x58000000)	//ADC control
#define rADCTSC    (*(volatile unsigned *)0x58000004)	//ADC touch screen control
#define rADCDLY    (*(volatile unsigned *)0x58000008)	//ADC start or Interval Delay
#define rADCDAT0   (*(volatile unsigned *)0x5800000c)	//ADC conversion data 0
#define rADCDAT1   (*(volatile unsigned *)0x58000010)	//ADC conversion data 1
#define rADCUPDN   (*(volatile unsigned *)0x58000014)	//Stylus Up/Down interrupt status


// SPI       
#define rSPCON0    (*(volatile unsigned *)0x59000000)	//SPI0 control
#define rSPSTA0    (*(volatile unsigned *)0x59000004)	//SPI0 status
#define rSPPIN0    (*(volatile unsigned *)0x59000008)	//SPI0 pin control
#define rSPPRE0    (*(volatile unsigned *)0x5900000c)	//SPI0 baud rate prescaler
#define rSPTDAT0   (*(volatile unsigned *)0x59000010)	//SPI0 Tx data
#define rSPRDAT0   (*(volatile unsigned *)0x59000014)	//SPI0 Rx data

#define rSPCON1    (*(volatile unsigned *)0x59000020)	//SPI1 control
#define rSPSTA1    (*(volatile unsigned *)0x59000024)	//SPI1 status
#define rSPPIN1    (*(volatile unsigned *)0x59000028)	//SPI1 pin control
#define rSPPRE1    (*(volatile unsigned *)0x5900002c)	//SPI1 baud rate prescaler
#define rSPTDAT1   (*(volatile unsigned *)0x59000030)	//SPI1 Tx data
#define rSPRDAT1   (*(volatile unsigned *)0x59000034)	//SPI1 Rx data


// SD Interface
#define rSDICON     (*(volatile unsigned *)0x5a000000)	//SDI control
#define rSDIPRE     (*(volatile unsigned *)0x5a000004)	//SDI baud rate prescaler
#define rSDICARG    (*(volatile unsigned *)0x5a000008)	//SDI command argument
#define rSDICCON    (*(volatile unsigned *)0x5a00000c)	//SDI command control
#define rSDICSTA    (*(volatile unsigned *)0x5a000010)	//SDI command status
#define rSDIRSP0    (*(volatile unsigned *)0x5a000014)	//SDI response 0
#define rSDIRSP1    (*(volatile unsigned *)0x5a000018)	//SDI response 1
#define rSDIRSP2    (*(volatile unsigned *)0x5a00001c)	//SDI response 2
#define rSDIRSP3    (*(volatile unsigned *)0x5a000020)	//SDI response 3
#define rSDIDTIMER  (*(volatile unsigned *)0x5a000024)	//SDI data/busy timer
#define rSDIBSIZE   (*(volatile unsigned *)0x5a000028)	//SDI block size
#define rSDIDCON    (*(volatile unsigned *)0x5a00002c)	//SDI data control
#define rSDIDCNT    (*(volatile unsigned *)0x5a000030)	//SDI data remain counter
#define rSDIDSTA    (*(volatile unsigned *)0x5a000034)	//SDI data status
#define rSDIFSTA    (*(volatile unsigned *)0x5a000038)	//SDI FIFO status
#define rSDIIMSK    (*(volatile unsigned *)0x5a00003c)	//SDI interrupt mask

#ifdef __BIG_ENDIAN
#define rSDIDAT    (*(volatile unsigned *)0x5a000040)	//SDI data
#else  // Little Endian
#define rSDIDAT    (*(volatile unsigned *)0x5a000040)	//SDI data
#endif   //SD Interface

#define _ISR_STARTADDRESS   ((unsigned)isr_handle_array)
// Exception vector
#define pISR_RESET		(*(unsigned *)(_ISR_STARTADDRESS+0x0))
#define pISR_UNDEF		(*(unsigned *)(_ISR_STARTADDRESS+0x4))
#define pISR_SWI		(*(unsigned *)(_ISR_STARTADDRESS+0x8))
#define pISR_PABORT		(*(unsigned *)(_ISR_STARTADDRESS+0xc))
#define pISR_DABORT		(*(unsigned *)(_ISR_STARTADDRESS+0x10))
#define pISR_RESERVED	(*(unsigned *)(_ISR_STARTADDRESS+0x14))
#define pISR_IRQ		(*(unsigned *)(_ISR_STARTADDRESS+0x18))
#define pISR_FIQ		(*(unsigned *)(_ISR_STARTADDRESS+0x1c))
// Interrupt vector
#define pISR_EINT0		(*(unsigned *)(_ISR_STARTADDRESS+0x20))
#define pISR_EINT1		(*(unsigned *)(_ISR_STARTADDRESS+0x24))
#define pISR_EINT2		(*(unsigned *)(_ISR_STARTADDRESS+0x28))
#define pISR_EINT3		(*(unsigned *)(_ISR_STARTADDRESS+0x2c))
#define pISR_EINT4_7	(*(unsigned *)(_ISR_STARTADDRESS+0x30))
#define pISR_EINT8_23	(*(unsigned *)(_ISR_STARTADDRESS+0x34))
#define pISR_CAM		(*(unsigned *)(_ISR_STARTADDRESS+0x38))		// Added for 2440.
#define pISR_BAT_FLT	(*(unsigned *)(_ISR_STARTADDRESS+0x3c))
#define pISR_TICK		(*(unsigned *)(_ISR_STARTADDRESS+0x40))
#define pISR_WDT_AC97	(*(unsigned *)(_ISR_STARTADDRESS+0x44))
#define pISR_TIMER0	 	(*(unsigned *)(_ISR_STARTADDRESS+0x48))
#define pISR_TIMER1	 	(*(unsigned *)(_ISR_STARTADDRESS+0x4c))
#define pISR_TIMER2		(*(unsigned *)(_ISR_STARTADDRESS+0x50))
#define pISR_TIMER3		(*(unsigned *)(_ISR_STARTADDRESS+0x54))
#define pISR_TIMER4		(*(unsigned *)(_ISR_STARTADDRESS+0x58))
#define pISR_UART2		(*(unsigned *)(_ISR_STARTADDRESS+0x5c))
#define pISR_LCD		(*(unsigned *)(_ISR_STARTADDRESS+0x60))
#define pISR_DMA0		(*(unsigned *)(_ISR_STARTADDRESS+0x64))
#define pISR_DMA1		(*(unsigned *)(_ISR_STARTADDRESS+0x68))
#define pISR_DMA2		(*(unsigned *)(_ISR_STARTADDRESS+0x6c))
#define pISR_DMA3		(*(unsigned *)(_ISR_STARTADDRESS+0x70))
#define pISR_SDI		(*(unsigned *)(_ISR_STARTADDRESS+0x74))
#define pISR_SPI0		(*(unsigned *)(_ISR_STARTADDRESS+0x78))
#define pISR_UART1		(*(unsigned *)(_ISR_STARTADDRESS+0x7c))
#define pISR_NFCON		(*(unsigned *)(_ISR_STARTADDRESS+0x80))		// Added for 2440.
#define pISR_USBD		(*(unsigned *)(_ISR_STARTADDRESS+0x84))
#define pISR_USBH		(*(unsigned *)(_ISR_STARTADDRESS+0x88))
#define pISR_IIC		(*(unsigned *)(_ISR_STARTADDRESS+0x8c))
#define pISR_UART0		(*(unsigned *)(_ISR_STARTADDRESS+0x90))
#define pISR_SPI1		(*(unsigned *)(_ISR_STARTADDRESS+0x94))
#define pISR_RTC		(*(unsigned *)(_ISR_STARTADDRESS+0x98))
#define pISR_ADC		(*(unsigned *)(_ISR_STARTADDRESS+0x9c))


// PENDING BIT
#define BIT_EINT0		(1<<0)
#define BIT_EINT1		(1<<1)
#define BIT_EINT2		(1<<2)
#define BIT_EINT3		(1<<3)
#define BIT_EINT4_7		(1<<4)
#define BIT_EINT8_23	(1<<5)
#define BIT_CAM			(1<<6)		// Added for 2440.
#define BIT_BAT_FLT		(1<<7)
#define BIT_TICK		(1<<8)
#define BIT_WDT_AC97	(1<<9)
#define BIT_TIMER0		(1<<10)
#define BIT_TIMER1		(1<<11)
#define BIT_TIMER2		(1<<12)
#define BIT_TIMER3		(1<<13)
#define BIT_TIMER4		(1<<14)
#define BIT_UART2		(1<<15)
#define BIT_LCD			(1<<16)
#define BIT_DMA0		(1<<17)
#define BIT_DMA1		(1<<18)
#define BIT_DMA2		(1<<19)
#define BIT_DMA3		(1<<20)
#define BIT_SDI			(1<<21)
#define BIT_SPI0		(1<<22)
#define BIT_UART1		(1<<23)
#define BIT_NFCON		(1<<24)		// Added for 2440.
#define BIT_USBD		(1<<25)
#define BIT_USBH		(1<<26)
#define BIT_IIC			(1<<27)
#define BIT_UART0		(1<<28)
#define BIT_SPI1		(1<<29)
#define BIT_RTC			(1<<30)
#define BIT_ADC			(1<<31)
#define BIT_ALLMSK		(0xffffffff)

#define BIT_SUB_ALLMSK	(0x7fff)
#define BIT_SUB_AC97 	(1<<14)
#define BIT_SUB_WDT 	(1<<13)
#define BIT_SUB_CAM_S	(1<<12)		// Added for 2440.
#define BIT_SUB_CAM_C	(1<<11)		// Added for 2440.
#define BIT_SUB_ADC		(1<<10)
#define BIT_SUB_TC		(1<<9)
#define BIT_SUB_ERR2	(1<<8)
#define BIT_SUB_TXD2	(1<<7)
#define BIT_SUB_RXD2	(1<<6)
#define BIT_SUB_ERR1	(1<<5)
#define BIT_SUB_TXD1	(1<<4)
#define BIT_SUB_RXD1	(1<<3)
#define BIT_SUB_ERR0	(1<<2)
#define BIT_SUB_TXD0	(1<<1)
#define BIT_SUB_RXD0	(1<<0)

#endif
